SERAX Encensoir S Candle: Care and Even-Burn Tips
By Cutipol: The Shape of Tomorrow’s Cuisine | Official Store | Published: 2026-11-01
Category: Tips & Care
Keep the SERAX Encensoir S candle burning evenly and smelling clean with a simple trim, burn, and tunneling-fix routine for its 45-hour life.
Quick answer
Trim the wick to about 5 mm before every burn, let the Encensoir S burn until the wax melts to the edge of the pot, and never burn it longer than four hours at a time. These three habits prevent tunneling and keep the carnation, geranium, and white-flower scent clean for its full 45-hour life.
Why the lidded pot changes your routine
The Encensoir S comes in a lidded ceramic pot designed by Bela Silva, so the candle is both a scent source and a decorative container. That lid is useful for keeping dust off the wax between burns, but it also means you should never leave the lid on while burning. Check that the wax surface is free of dust and debris before each light-up, since a covered pot can collect particles that will smoke or smell when heated.
When to stop burning and let it reset
A common mistake is burning a scented candle for hours to "use it up." With a pot this size, long sessions overheat the wax and can cause the wick to mushroom, which leads to soot and an uneven melt. If the flame becomes tall or starts to flicker heavily, extinguish it, let the wax cool completely, and trim the wick again before relighting. Treat the 45-hour burn time as a guide for total life, not a target for one session.
Step-by-step Encensoir S care routine
- Trim the wick before every burn: Use a wick trimmer or small scissors to cut the wick to about 5 mm (1/4 inch) while the wax is cool. Remove any trimmed bits from the wax surface. A long or crooked wick is the most common cause of soot and an uneven melt.
- Set a first-burn checkpoint: On the first burn, let the candle stay lit until the melted wax reaches the inner edge of the pot, usually within two to three hours. Do not stop early, even if the scent is already strong. A full first melt pool sets the memory of the wax and reduces tunneling later.
- Keep sessions to four hours or less: Extinguish the candle after about four hours, or sooner if the flame grows tall or flickers. Let the wax cool completely before relighting. Short sessions protect the wick and keep the floral scent from turning smoky.
- Fix tunneling with a foil wrap: If wax tunnels around the wick, wrap a piece of aluminum foil around the top of the pot, leaving a small opening over the wick, and burn for one to two hours. This traps heat and melts the side wax. Never leave this setup unattended. Only use the foil method on a level, heat-safe surface and check it every 15 minutes.
- Store with the lid between burns: Once the wax is fully cool, place the lid back on the pot to keep dust and debris off the surface. Keep the candle away from direct sunlight and heat. A covered pot stays clean, so the next burn smells like carnation and geranium, not dust.
Product facts
- SERAX Scented Candles - Candle Ivory Encensoir S: The Encensoir scented candle burns for up to 45 hours. Knowing the total burn time helps you plan shorter, even sessions instead of long marathons that waste wax.
SERAX Scented Candles - Candle Ivory Encensoir S - SERAX Scented Candles - Candle Ivory Encensoir S: The scent combines carnation, geranium, and white flowers. These soft floral notes stay truest when the wax pool is clean and the wick is trimmed, so maintenance protects the fragrance.
- SERAX Scented Candles - Candle Ivory Encensoir S: The candle is housed in a lidded pot that doubles as a decorative object and storage container. Use the lid to keep the wax dust-free between burns, but always remove it while the candle is lit.
